Wishlist
Best sellers
-
Hi Torque QRS Clutch Rollers
For 2008-to present Skidoo XP/XS/XM & G4/G5 QRS Driven...
-
G4 Engine Mount Torque Stop
This is a new polyurethane motor mount torque stop that replaces the...
-
Brace Kit Bundle
These are our a arm brace kits bundled into one deal. Buy both and get a...
Manufacturers
Suppliers
No supplier
Best sellers
AvailableG4/G5 E Module Brace Kit
G4G5 E Module brace kit, similar to the BRP reinforcement plate but with improvements. This kit reinforces the entire area under the y pipe. The cross piece is known to break and the outside upper a arm areas can also crack. So this reinforces those areas known to fail.25% thicker aluminum than the BRP plate. G N R text cut into the center section to allow air to flow under the motor and to primary clutch area. BRP's plate completely...
G4G5 E Module brace kit, similar to the BRP reinforcement plate but with improvements....
G4G5 E Module brace kit, similar to the BRP reinforcement plate but with improvements. This kit reinforces the entire area under the y pipe. The cross piece is known to break...
AvailableArctic Cat Rear Spring...
Don't get stranded on the trail or the track with the breakable plastic blocks. Replace them with these unbreakable CNC machined billet aluminum blocks. Redesigned with a 10% increase in spring preload in the medium position and a 15% increase in the high position. Very light weight thru hole design. For all Arctic Cat models. Fits the Catalyst SOLD AS A PAIR
Don't get stranded on the trail or the track with the breakable plastic blocks. Replace...
Don't get stranded on the trail or the track with the breakable plastic blocks. Replace them with these unbreakable CNC machined billet aluminum blocks. Redesigned with a 10%...
AvailableProcross/Proclimb...
NEW billet aluminum rear axle track adjuster blocks for the 2012-present Procross/Proclimb chassis. These replace the weak die cast stock aluminum adjuster that can break, see picture Easy installation. Remove the axle bolt and washer, pull the rail towards you and remove the stock adjuster. Slide the billet adjuster in it's place and reinstall the bolt and washer. Sold in pairs DOES NOT FIT 2020 X-TX LE SIDEWINDER ONLY FITS THE SIDEWINDER IF...
NEW billet aluminum rear axle track adjuster blocks for the 2012-present...
NEW billet aluminum rear axle track adjuster blocks for the 2012-present Procross/Proclimb chassis. These replace the weak die cast stock aluminum adjuster that can break, see...
AvailableP Drive Clutch Tool Kit 2
Here are the tools needed to work on the P Drive primary clutch. Our Tool Kit-2 includes everything needed to take apart and reassemble the p drive Primary clutch. Does not do the secondary clutch. If you need to do both clutches then you need to order p drive 3 kit. P Drive Kit-2 includes the following:Clutch HolderPuller BoltCirclip remover/installerPin removal toolCompressor with Base/Nut with handle Aluminum Spacer to support Clutch 3...
Here are the tools needed to work on the P Drive primary clutch. Our Tool Kit-2...
Here are the tools needed to work on the P Drive primary clutch. Our Tool Kit-2 includes everything needed to take apart and reassemble the p drive Primary clutch. Does not do...
AvailableSKI-DOO XM T-MOTION...
Scroll to the bottom of the page to see the download application that is a brown box with a green arrow in it. This gives the install instructions Torsion spring spacers add pre-load to the rear torsion spring system increasing its pre-load and effective rate during compression. Includes (1) Pair of Torsion Spring Spacers for Ski Doo T-Motion equipped snowmobiles. Fits: 2012+ Summit XM with T-Motion Skid including 2017+ G4 Summits with...
Scroll to the bottom of the page to see the download application that is a brown box...
Scroll to the bottom of the page to see the download application that is a brown box with a green arrow in it. This gives the install instructions Torsion spring spacers add...
AvailableG4/G5 Belly Brace/Skid...
This is a 1/8" thick aluminum plate that braces your rear lower a arm mounting point and also covers the thin aluminum belly pan. Protects the vulnerable belly pan from impacts. Will fit under a plastic skid plate, installs with 3/16" rivets. This brace/skid plate has the same rivet pattern as our steel brace in our G4 front end brace kit so you can replace that steel brace with this combination brace/skid plate.
This is a 1/8" thick aluminum plate that braces your rear lower a arm mounting point...
This is a 1/8" thick aluminum plate that braces your rear lower a arm mounting point and also covers the thin aluminum belly pan. Protects the vulnerable belly pan from...
AvailableG4 .031" Mag Side...
Aluminum .031" thick shim designed to shim the Mag side motor mount to align clutches. Includes one shim
Aluminum .031" thick shim designed to shim the Mag side motor mount to align clutches....
Aluminum .031" thick shim designed to shim the Mag side motor mount to align clutches. Includes one shim
AvailableQRS Shim Kit 0.5mm
Many clutches are misaligned right from the factory. This kit will allow you to shim your QRS driven clutch out using 0.5mm (.020") thick shims. The kit includes 3 of each shim for a total of 1.5mm (.060") of adjustment when stacked. Allows for fine tuning the offset on your sled.Installation is easy and detailed instructions are included. These shims can be stacked.Fits 2008-2018 sleds with QRS secondary clutch.
Many clutches are misaligned right from the factory. This kit will allow you to shim...
Many clutches are misaligned right from the factory. This kit will allow you to shim your QRS driven clutch out using 0.5mm (.020") thick shims. The kit includes 3 of each shim...
AvailableISO G4/G5 for adj riser
Fits GEN4/5 850 with forward/rearward adjustable riser. Also fits the height adjustable riser. Skidoo Isovibe SX model absorbs shock in the forward and rearward direction just like the original design but now absorbs shock in the vertical and side to side direction. The main goal for this design was to absorb the shock normally transferred to your wrists, shoulders and arms when landing jumps or hitting hard bumps with one ski. If you've even...
Fits GEN4/5 850 with forward/rearward adjustable riser. Also fits the height adjustable...
Fits GEN4/5 850 with forward/rearward adjustable riser. Also fits the height adjustable riser. Skidoo Isovibe SX model absorbs shock in the forward and rearward direction just...
AvailableG4 Clutch Side Motor...
Aluminum .062" thick shim designed to shim the Clutch side motor mounts to align clutches. Includes one shim
Aluminum .062" thick shim designed to shim the Clutch side motor mounts to align...
Aluminum .062" thick shim designed to shim the Clutch side motor mounts to align clutches. Includes one shim
AvailableQRS Bearing Puller
The QRS Bearing Puller is used to remove and install the Shaft Bearing on all QRS Secondary Clutches from 2008 to current Ski-Doo snowmobiles. The threaded rod IS NOT included with this bearing puller. Customer will need to purchase the threaded rod, nuts & washers. By doing this, the customer will save on the increased shipping charges. Detailed instructions on what to purchase as well as bearing removal are included. The...
The QRS Bearing Puller is used to remove and install the Shaft Bearing on all QRS...
The QRS Bearing Puller is used to remove and install the Shaft Bearing on all QRS Secondary Clutches from 2008 to current Ski-Doo snowmobiles. The threaded rod IS NOT...
AvailableG5 Accessory Power Plug
The G5 chassis changed from a 2 wire to a 3 wire plug on the power under the dash just above the driven clutch. Use this harness to plug into the sleds 12 volt accessory system to power anything you want such as LED lights. Use the red and black wires to power a 12volt accessory when the sled is running. Use the grey and black wires to power a 12 volt accessory when the high beams are on. Tape over the extra wire that you aren't using.Comes...
The G5 chassis changed from a 2 wire to a 3 wire plug on the power under the dash just...
The G5 chassis changed from a 2 wire to a 3 wire plug on the power under the dash just above the driven clutch. Use this harness to plug into the sleds 12 volt accessory system...
